Reconditioned Valeo starter motor and solenoid in black and silver finish. Professionally reconditioned and sold with a 12 month guarantee. This is a suitable replacement for Bosch 8 or 9 tooth Guzzi starter motors. Minor modification may be required on some pre 1990 models to make room for the solenoid. Please note that this item may be fitted to Loop frame models with some modifications as described in Guzziology. See , see this link for the modifications required to fit a Valeo starter to a 4 speed model.

This is an exchange only item, we can supply these before receiving your exchange unit subject to a refundable deposit so you can keep your bike on the road. See ELC10737 for the refundable deposit. Send your old starter motor to our registered address. NB In case of starter motor problems do not tap the casing as this will certainly cause it to fail. See SSA08075 for mounting bolts. Also known as Guzzi ref. 30730710
Do not remove second nut from terminal posts when fitting - this nut is required to hold the terminal in place

Supercedes Guzzi refs. 12730705, 14730554 and 14730705

 30730711 GU30730711 30 73 07 11
 3073 0711 3073.0711 30.73.07.11

Spark plug cap

Also known as suppressor cap Guzzi ref 2D000005 and GU02717450. See ELA02450 for less expensive alternative

 This part is available by special order, request a quote

2D000247

Speedo sensor with 100cm lead and 3 pin plug for non-ABS models

 This part is due back in stock soon, call 01484 841395 to reserve yours

AP8124528

Also fits Aprilia Falco (2000-2003)

The Power Commander is a fuel injection and ignition timing (on some models) adjustment unit that plugs "inline" with the bikes' stock ECU. The Power Commander uses original equipment style connectors so that no splicing or cutting of the harness is required. Most installations take less than 15 minutes, some as little as 5 minutes. Changes are made to the bikes fuel and ignition curves via the Power Commander's onboard microprocessor. Using this technology we are able to offer a large area of adjustment without making any permanent changes to the bikes' ECU (electronic control unit). Removing the Power Commander returns the bike to its previous stock condition. The Power Commander can be ordered preprogrammed with a your choice of several settings, based on the modifications to your bike. The unit also comes complete with software and cable link that allows you to change between different maps or make adjustments to a map file.

This is for V7 models with twin throttle bodies, it is not compatible with single throttle body models

 This part is available by special order, request a quote

High performance Quadflex maintenance free Motobatt 12 volt 16.5Ah battery. Quadflex technology means you have two positive and two negative threaded terminals allowing maximum flexibility when installing. Motobatt absorbed gel matting batteries feature the latest absorbent glass mat technology and offer superior cranking power (210 CCA). This offers increased lifespan, higher vibration resistance and electrical performance. This battery is also leak, vibration and spill proof if installed correctly.
For models listed with twin throttle bodies

Supplied charged and ready to fit with terminal brackets and button head screws. Can be used to replace OE Yuasa battery Guzzi ref. 640201
NB This battery must not be trickle charged or charged using a traditional manual charger, AGM batteries require a smart charger - we recommend ACA96000
For more information on charging AGM batteries see these FAQ's.
This battery is for dual throttle body small twins.

One year warranty on all our Motobatt batteries.

Also available at the same price in black by special order - call 01484 841395 to order

Please note this part CANNOT be posted outside of the UK mainland area

 Order now and we will post your order within 7 days.

 01180114 GU01180114 01 18 01 14
 0118 0114 0118.0114 01.18.01.14

Complete electronic ignition kit containing alternator mounted ignition pickup, fittings and amplifier unit. Works with standard 3 Ohm 12 volt coils and can be used to replace points or Motoplat ignition on models with Saprisa charging systems. The pickups for this kit are mounted on the alternator stator. Supplied with instructions in German with wiring diagrams.

2 year warranty on Sachse ignition kits

Eliminates vague timing due to worn distributors on big twins. Preloaded with nine ignition curves, two of which are designed for twin plugged bikes. Once fitted no further adjustment should be necessary. See this link for fitting instructions. Note that if you are replacing a Digiplex system you will also need to replace your 'square' coils with higher impedance 12 volt coils e.g. ELA31165

 This part is available by special order, request a quote

Brand new genuine Valeo starter motor and solenoid suitable as a direct replacement for Guzzi Valeo and Bosch 8 or 9 teeth starter motors. You may need to fit hex headed neutral switch bolts on some pre 1990 models to make room for the solenoid. Our part number for the bolt is SSA06016
Please note that this item may be fitted to Loop frame models with some modifications as described in Guzziology, also see https://www.thisoldtractor.com/moto_guzzi_loopframe_starter_-_how_to_replace_the_magneti_marelli_starter_with_a_valeo.html for advice on this upgrade.

This is a genuine Valeo starter made in the EU- please do not confuse with the cheap Chinese copies that sometimes appear on eBay.

Supercedes Guzzi refs. 12730705, 14730554 and 14730705

Please note you can get a discount of £30 on this item if you part exchange your existing faulty starter motor. See ELA30837 for less expensive alternative part

 This part is due back in stock soon, call 01484 841395 to reserve yours

 30730711 GU30730711 30 73 07 11
 3073 0711 3073.0711 30.73.07.11

Support for oil temperature sensor

 This part is available by special order, request a quote

 03163330 GU03163330 03 16 33 30
 0316 3330 0316.3330 03.16.33.30

Brakelight switch for handlebar mounted master cylinder

Stop light switch also known as Guzzi ref. 30530526. Please compare with your existing switch to check compatibility. Can be used as a substitute for ELA27815 or ELA30860. Sometimes supplied with three terminals, in this instance disregard middle terminal. Please note that terminals are smaller than standard switch and will need to be soldered on.

 This part is due back in stock soon, call 01484 841395 to reserve yours

 30749860 GU30749860 30 74 98 60
 3074 9860 3074.9860 30.74.98.60

Sidestand cutout switch

See ELA81319 for rotary switch that was fitted to some models

 This part is available by special order, request a quote

 639542 MG639542